Problem with dcmprscu

[jerzy_cz]

Hello, I'm trying to connect to Dicom printer emulator using dcmprscu. I always get an error "unable to create basic film box." What is wrong?
Debug information:

dcmprscu database\SP*.dcm -c dcmpstat.cfg -p DVT -v +d

Printer parameters for 'DVT':
hostname : localhost
port : 104
description : IHE Full Print SCP
aetitle : STORESCP
max pdu : 32768
timeout : -1
options : none.
12-bit xfer : supported
present.lut : not supported
annotation : not supported

Spooler parameters:
mode : printer mode
copies : 0
medium : printer default
destination : printer default
label : printer default
priority : printer default
owner ID : printer default

transport layer security parameters:
TLS : disabled

spooling file 'database\SP_47205584d97d91a2.dcm'
Requesting Association
Association accepted (Max Send PDV: 16372)
===================== OUTGOING DIMSE MESSAGE ====================
Message Type : N-GET RQ
Message ID : 1
Requested SOP Class UID : PrinterSOPClass
Requested SOP Instance UID : 1.2.840.10008.5.1.1.17
Data Set : none
Attribute Identifier List : none
======================= END DIMSE MESSAGE =======================

===================== INCOMING DIMSE MESSAGE ====================
Message Type : N-GET RSP
Message ID Being Responded To : 1
Affected SOP Class UID : PrinterSOPClass
Affected SOP Instance UID : 1.2.840.10008.5.1.1.17
Data Set : present
DIMSE Status : 0x0000: Success

# Dicom-Data-Set
# Used TransferSyntax: BigEndianExplicit
(0008,0070) LO [DVT] # 4, 1 Manufacturer
(0008,1090) LO [DVT] # 4, 1 ManufacturersModelName
(0018,1000) LO [123456] # 6, 1 DeviceSerialNumber
(0018,1020) LO [Version 2.0] # 12, 1 SoftwareVersions
(0018,1200) DA [20071025] # 8, 1 DateOfLastCalibration
(0018,1201) TM [103745] # 6, 1 TimeOfLastCalibration
(2110,0010) CS [NORMAL] # 6, 1 PrinterStatus
(2110,0030) LO [dvt] # 4, 1 PrinterName
======================= END DIMSE MESSAGE =======================

spooler: warning: printer does not support Presentation LUT SOP Class,
presentation LUT related print job settings will be ignored.
===================== OUTGOING DIMSE MESSAGE ====================
Message Type : N-CREATE RQ
Message ID : 2
Affected SOP Class UID : BasicFilmSessionSOPClass
Affected SOP Instance UID : none
Data Set : none

# Dicom-Data-Set
# Used TransferSyntax: UnknownTransferSyntax
======================= END DIMSE MESSAGE =======================

===================== INCOMING DIMSE MESSAGE ====================
Message Type : N-CREATE RSP
Message ID Being Responded To : 2
Affected SOP Class UID : BasicFilmSessionSOPClass
Affected SOP Instance UID :
Data Set : none
DIMSE Status : 0x0000: Success
======================= END DIMSE MESSAGE =======================

spooler: printer communication failed, unable to create basic film box.
spooler: release of connection to printer failed.
0006:0317 Peer aborted Association (or never connected)
error: spooling of file 'database\SP_47205584d97d91a2.dcm' failed.

[Marco Eichelberg]

I would guess that you have discovered a bug in the "printer emulator", which is obviously unable to generate a SOP instance UID upon N-CREATE, which is a required feature for a Print SCP.

[alwittta]

Dear DCMTK team,

Could anyone please tell me is this bug fixed?

Thanks and Regards
Alvin

[nicolasdicom]

Hi all!

Code: Select all

spooler: printer communication failed, unable to create basic film box.
spooler: release of connection to printer failed.
0006:0317 Peer aborted Association (or never connected)
error: spooling of file 'database\SP_47205584d97d91a2.dcm' failed.

Bug in the virtual printer ...

Well, i am not sure, but i guess I had the same error message using a FUJI DRYPIX3000 . I have to check it out again. I will do it soon, by the moment the power supply of our DICOM printer died .
LooL. Wasn't my fault !

Regards,

Nicolas